700

Material:  Steel Method Used:  etch Depth:  >.003 Laser Type:  20 Watt Q-Switch Fiber Laser Focal Length Lens:  160mm Power: 98% Frequency: 20 kHz Speed: 15 inches per second Passes: 20 Cycle Time: 1176 seconds Samples wereRead More…

681

Material:  Steel Power:  100% Method Used:  Laser annealing Frequency:  55kHz Depth:  Surface Speed:  300mm/sec Laser Type:  Pulsed fiber laser (1064nm, 1mJ @ 20kHz) Passes: 2 Focal Length Lens:  100mm Cycle Time:  104sec   Sample was markedRead More…

620

The part was marked using a 20 watt q-switched ytterbium fiber laser with 160mm focal length lens. The small and medium drill bits were surface annealed at approximately 17 watts of power,Read More…

622

The parts were marked using a 20 Watt Pulsed Fiber Laser using a 420mm lens. Three trials were made. The fastest marking trial was when 12 Watts of power was used withRead More…

623

This steel tool was marked using a 20 Watt Fiber Laser Marking System

626

The part was marked using a 20 Watt Fiber Laser Marking System  

627

The part was marked with a 20 watt Q-switched Ytterbium fiber laser and 160 mm focal length lens. The sample was ablated with the information provided by customer to create a niceRead More…

628

The samples were marked using a 20 watt Q-switched Fiber Laser using a 160 mm lens. The Colt logo (vector graphic) was annealed using 15 Watts of power, frequency of 80 kHz,Read More…

629

The parts were marked with a 20 watt q-switched ytterbium fiber laser and 160 mm focal length lens. Process Parameters: Material: Steel Power: 16 Watts Method used: Ablation Frequency: 80 kHz Depth:Read More…

631

The part was marked using a 20Watt Fiber Laser Marking System

634

Laser marking of the tool steel was accomplished with a 20 Watt fiber laser marking system. The tool steel was marked with dark marks, duplicating the example pieces sent to us. The part wasRead More…

635

Process Parameters: Large Parts – Dark Coating, Light Etch Material: Steel Power: 17 Watt Method used: Etching Frequency: 80 kHz Depth: Surface Speed: 3 inchsec Laser Type: Q-Switched Fiber Laser Focal Length Lens:Read More…

636

Process Parameters: Small Parts – Dark Coating, Light Etch Material: Steel Power: 17 Watt Method used: Etching Frequency: 80 kHz Depth: Surface Speed: 3 inchsec Laser Type: Q-Switched Fiber Laser Focal LengthRead More…

637

Process Parameters: Small Parts – No Coating, Anneal Material: Steel Power: 7 Watt Method used: Anneal Frequency: 35 kHz Depth: Surface Speed: 10 inchsec Laser Type: Q-Switched Fiber Laser Focal Length Lens: 160mmRead More…

651

Large format metal laser cutting detail: This sheet of metal was laser cut using the SBM1200FL; equiped with a fiber laser. Please contact us for more information.

653

Laser cutting of this sawtooth was created using the SMB1200FL fiber laser cutting system.

539

This steel bit was marked using a 20 Watt Fiber Laser Marking System

556

The samples were marked using a 20 watt Q-switched Fiber Laser using a 160 mm lens. The Colt logo (vector graphic) was annealed using 15 Watts of power, frequency of 80 kHz,Read More…

557

This steel tool was marked using a 20 Watt Fiber Laser Marking System

559

This steel tool was marked using a 20 Watt Fiber Laser Marking System

560

This steel tool was marked using a 20 Watt Fiber Laser Marking System

561

This steel wheel was marked using a 20 Watt Fiber Laser Marking System  

564

The scissor was mark using the 20 watt q-switched ytterbium fiber laser, along with a 160 mm focal length lens. The scissor was marked with an annealed surface mark. The cycle timeRead More…

565

This steel tool was marked using a 20 Watt Fiber Laser Marking System

566

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

567

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

568

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

569

The scissor blades were laser marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

570

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

571

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

572

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

574

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

575

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

576

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser marking system, along with a 160mm focal length lens. The blades were marked with a dark surface mark. EachRead More…

577

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

578

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

579

The scissor blades were marked using a 20 watt q-switched ytterbium fiber laser, along with a 160mm focal length lens. The blades were marked with a dark surface mark. Each mark wasRead More…

581

The tool steel was marked with a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The part was laser engraved (deep engraved) according to customer specifications. The partRead More…

582

The tool steel was marked with a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The part was deep engraved according to customer specifications. The part was markedRead More…

584

The carbide, oxide coated and stainless steel were marked with a surface etch, the stainless steel was marked with a dark mark as well. A light etch is produces the most contrastRead More…

585

The parts were marked using a 20 Watt Pulsed Fiber Laser using a 420 mm lens. All three samples were annealed with the speed of 3" per second using frequency of 80Read More…

586

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens. A dark surface mark was put on the part.

587

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens. A dark surface mark was put on the part.

588

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens.  The cycle times for the part was below one second.

589

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens.  The cycle times for the part was below one second.

590

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens.  The cycle times for the part was below one second.

591

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens. The mark on this brown-coated nut remover had a cycle time of 0.88 seconds.  

592

This part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens. A dark surface mark was put on the part. The marks placed on the large tap hadRead More…

593

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens. A dark surface mark was put on the part.

594

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens.  The cycle times for the part was below one second.

595

The parts were marked using a 20Watt Fiber Laser Marking System using a 160 mm lens. The marks on the small spiral screw remover had 0.95 second cycle time.  

596

The parts were marked using a 20Watt Fiber Laser Marking System using a 160 mm lens. The marks on the large spiral screw remover had a 1.01 second cycle time.

597

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens.  The cycle times for the part was below one second.  

598

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens.  The cycle times for the part was below one second.  

599

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens.  The cycle times for the part was below one second.  

600

The parts were marked with a 10 watt q-switched ytterbium fiber laser and 160 mm focal length lens. The 160mm focal length lens has a working distance of 176mm from lens toRead More…

604

The part was marked using a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The 160mm focal length lens has a working distance of 176mm from lens toRead More…

605

The part was marked using a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The 160mm focal length lens has a working distance of 176mm from lens toRead More…

607

This steel tool was marked using a 20 Watt Fiber Laser Marking System

608

The parts were marked with a 20 watt q-switched ytterbium fiber laser and 254 mm focal length lens. The 254mm focal length lens has a working distance of 296mm from lens toRead More…

609

The parts were marked with a 20 watt q-switched ytterbium fiber laser and 254 mm focal length lens. The 254mm focal length lens has a working distance of 296mm from lens toRead More…

611

The high carbon steel darkened very easily using the 20 watt q-switched ytterbium fiber laser. The parts were marked using a 160 mm focal length lens. The short focal length lens producedRead More…

614

This steel tool was marked using a 20 Watt Fiber Laser Marking System

376

Laser cut steel

377

Laser marking on steel was accomplished using a 20 Watt Fiber Laser  

379

Laser marking on steel accomplished using a 20 Watt Fiber Laser

380

Laser marking on steel accomplished using a 20 Watt Fiber Laser

381

Laser engraved steel.

388

Laser marking on steel accomplished using a 20 Watt Fiber Laser

389

Laser marking on steel accomplished using a 20 Watt Fiber Laser

395

The parts were laser ablated with a 10 watt q-switched ytterbium fiber laser and 420 mm focal length lens. The 420mm focal length lens has a working area of 420mm square. TheRead More…

397

Laser marking on stainless steel accomplished using a 20 Watt Fiber Laser

398

Laser marking on steel accomplished using a 20 Watt Fiber Laser

399

Laser marking on steel accomplished using a 20 Watt Fiber Laser

400

Laser marking on steel accomplished using a 20 Watt Fiber Laser

401

Laser marking on steel accomplished using a 20 Watt Fiber Laser

402

Laser marking on steel accomplished using a 20 Watt Fiber Laser

418

The sample was marked with a 10 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The 160mm focal length lens has a working distance of 176mm from lens to part.Read More…

425

This steel sample was marked using a 20 watt Fiber laser marking system. The piece was surface annealed, to remove the paint and create contrasting marks.    

428

The part was marked using a 20 watt q-switched ytterbium fiber laser with 160mm focal length lens. The patch was marked first, and the 2D code and text were marked on topRead More…

432

This part was marked using a 20 watt q-switched ytterbium fiber laser with a 160 mm focal length lense. The sample was surface etched, to create the light marks on the part. Samples were markedRead More…

439

Steel parts marked using a 20 Watt Fiber Laser Marking System.

441

The samples were marked with two different fonts to provide a “contrast” versus “cycle time” comparison. In addition, per the customer’s request, the two samples were marked on the contoured surfaces withoutRead More…

443

These steel parts were marked using a 20 Watt Fiber Laser Marking System.

444

This metal discs with a dark mark was marked with a 20 watt q-switched ytterbium fiber laser and required two passes. The first pass used 16 watts of power with a frequency ofRead More…

445

This steel part was marked using a 20 Watt Fiber Laser Marking System.

455

The logo was marked on three different materials, each with different cycle times. The materials used were aluminum, painted aluminum and steel. Two different sized logos were marked on the steel sample.Read More…

457

The logo was marked on three different materials, each with different cycle times. The materials used were aluminum, painted aluminum and steel. Two different sized logos were marked on the steel sample.Read More…

195

Logos laser marked onto steel

200

This part was marked with a 20 watt q-switched ytterbium fiber laser with a 160 mm focal length lens. The sample was laser engraved to create a deep mark that would not be damagedRead More…

205

Laser marked steel

206

Sample laser marking on steel

207

Laser marked steel

208

 Laser markings on steel             

209

This steel part was marked with a UID using a 20 Watt Fiber Laser Marking System.

215

The part was marked using the 20Watt Fiber Laser Marking System. A variety of marks were put on the part to widen the selection process while also demonstrating the fiber laser’s capabilities.Read More…

229

The steel gear was marked using a 20 Watt Q-Switched Fiber Laser with a 160 mm lens. Logo, human readable characters and their barcode, 2D matrix code were etched on the partRead More…

232

Laser marked steel

233

The cam shafts were marked with two types of mark. A dark mark as seen on the customer samples sent in with the application and a light etched mark. The light etchRead More…

234

The dark UID marking was done to duplicate the existing customer samples. To get the dark marks, multiple marking passes were needed. Three passes were needed total to the dark marks. TheRead More…

237

UID marking was done to duplicate the existing customer samples. To get the dark marks, multiple marking passes were needed. Three passes were needed total to the dark marks. The dark marksRead More…

241

The parts were marked with a 20 watt q-switched ytterbium fiber laser and 160 mm focal length lens. The parts were surface etched to remove a layer of material and create aRead More…

242

The parts were marked with a 20 watt q-switched ytterbium fiber laser and 160 mm focal length lens. The parts were surface etched to remove a layer of material and create aRead More…

243

The parts were marked using a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The parts were engraved, to create contrasting marks on the material. The parameters forRead More…

253

The part was marked using a 20 watt q-switched ytterbium fiber laser with 160mm focal length lens. The parts were mark according to customer request. The serial number S1811Y-RP was etched ontoRead More…

254

The part was marked using a 20 watt q-switched ytterbium fiber laser with 160mm focal length lens. The parts were mark according to customer request. The alphanumeric mark IRGCO, was etched ontoRead More…

255

Laser marked steel    

257

The parts were marked using a 10 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The parts were surface etched, to create brightly contrasting marks. The codes read wellRead More…

269

Laser marking on steel accomplished using a Fiber Laser

272

The UID was marked on this steel part using a 20 Watt Fiber Laser Marking System.

274

UID marking was done using a 20Watt Fiber Laser Marking System, a light etch was placed on the parts. A light etch was used due to the reflective nature of the metal,Read More…

275

The canisters were marked using the 20 watt q-switched ytterbium fiber laser, along with a 160 mm focal length lens. In order to get the marks along the outside diameter of theRead More…

276

The canisters were marked using the 20 watt q-switched ytterbium fiber laser, along with a 160 mm focal length lens. In order to get the marks along the outside diameter of theRead More…

277

The laser marking on this steel sample was accomplished using a Fiber Laser  

281

Laser marking on steel using a fiber laser

282

The airfoils were marked using a 20 Watt Pulsed Fiber Laser using a 160 mm lens. The text was engraved into the parts, 10 passes were used to mark the text. TwoRead More…

284

Laser marking on steel carbide accomplished by using a Fiber Laser    

285

 A laser marking on steel    

286

Laser marked steel, accomplished using a Fiber Laser    

287

The laser markings on this steel were accomplished using a Fiber Laser

293

UID marking was done using a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The parts were surface annealed, to create brightly contrasting marks. The parts were markedRead More…

294

Tooling: Precision twist drill bit marking.

295

Purolator – Automotive Marking The Purolator samples were marked using the 10 watt Fiber Laser Marking System. The ends of the filters were cut off to compensate for the fixed workstations hereRead More…

296

Purolator – Automotive Marking The Purolator samples were marked using the 10 watt Fiber Laser Marking System. The ends of the filters were cut off to compensate for the fixed workstations hereRead More…

298

These samples were laser marked using a fiber laser

299

This steel was laser marked using a fiber laser  

300

Laser marking was accomplished on steel by using a fiber laser    

304

The part was marked using a 20Watt Fiber Laser Marking System using a 160 mm lens. The part was marked with both a light etch and a dark surface mark. The lightRead More…

306

These steel samples were marked using a fiber laser

309

312

Laser marking on steel accomplished using a Fiber Laser  

313

Automotive: Marking on Steel Dipsticks

314

Marking: Clutchtex Clutch The part was marked using a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The metal oxide part was surface etched, to create brightly contrasting marks. TheRead More…

315

Marking: Teflon Coated Steel – Clutchtex Clutch The part was marked using a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The metal oxide part was surface etched, to createRead More…

317

This part was marked using a 20-watt q-switched fiber laser with 160 mm focal length lens. The part was annealed with logo and part number as requested. High contrast marks were achieved. Method:Read More…

318

This part was marked using a 20-watt q-switched fiber laser with 160 mm focal length lens. The part was annealed with logo and part number as requested. High contrast marks were achieved. Method:Read More…

319

This part was marked using a 20-watt q-switched fiber laser with 160 mm focal length lens. The part was annealed with logo and part number as requested. High contrast marks were achieved. Method:Read More…

320

UID marking was done with a 20 watt q-switched ytterbium fiber laser. The 160mm focal length lens has a working distance of 176mm from lens to part. The parts were marked withRead More…

325

UID markings were marked with a 20 watt q-switched ytterbium fiber laser. The 160mm focal length lens has a working distance of 176mm from lens to part. The parts were marked with UIDRead More…

326

UID marking was accomplished with a 20 watt q-switched ytterbium fiber laser. The 160mm focal length lens has a working distance of 176mm from lens to part. The parts were marked withRead More…

328

329

The Laser marking on this steel was accomplished using a 20 Watt Fiber Laser

330

The Laser marking on this steel was accomplished using a 20 Watt Fiber Laser

331

The Laser marking on this steel was accomplished using a 20 Watt Fiber Laser  

357

Using our LPQ series fiber laser configured with a 160mm focal length lens and testing various parameters, the automotive bearing was surface marked with 18 watts of power at 80 kHz andRead More…

368

Laser cut stainless steel.

119

This steel medical device was laser marked using a 20 Watt Fiber Laser marking system. Medical Device Marking: Process Parameters: Material: Steel Power: 20 Watt Method used: Surface Etch & Anneal Frequency: 20 &Read More…

120

This steel medical device was laser marked using a 20 Watt Fiber Laser marking system. Medical Device Marking: Process Parameters: Material: Steel Power: 20 Watt Method used: Surface Etch & Anneal Frequency: 20 &Read More…

121

This steel medical part was laser marked using a 20 Watt Fiber Laser. Medical Device Marking: Process Parameters: Material: Steel Power: 20 Watt Method used: Surface Etch & Anneal Frequency: 20 &Read More…

128

This medical device was marked using a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The sample was etched with the information provided by customer. Medical Device Marking: Material: SteelRead More…

142

The parts were laser marked using a 20Watt Fiber Laser Marking System with a 160mm lens. The 160mm focal length lens has a working distance of 176mm from lens to part. TwoRead More…

143

The parts were marked using a 20Watt Fiber Laser Marking System with a 160mm lens. The 160mm focal length lens has a working distance of 176mm from lens to part. Two differentRead More…

144

The parts were marked using a 20Watt Fiber Laser Marking System with a 160mm lens. The 160mm focal length lens has a working distance of 176mm from lens to part. Two differentRead More…

150

Laser marking on a steel sample  

152

A steel sample that was laser marked

157

Laser marking on steel

159

The parts were marked using a 20 Watt Pulsed Fiber Laser using a 160 mm lens. The samples were annealed to create brightly contrasting marks. The Brass sample was engraved and lightRead More…

160

The parts were marked using a 20 Watt Q-Switched Fiber Laser with a 160 mm lens. The handles were marked inside of the requested area designated with a pink box. The parts wereRead More…

161

Laser marking was accomplished using a 20 Watt Fiber Laser using a 160 mm lens. The steel was engraved using 18 Watts of power, frequency of 25 kHz, speed of 10" perRead More…

165

UID marking was accomplished with a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The small gear sample was marked on both sides. The side with the etchedRead More…

166

UID marking was accomplished with a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The small gear sample was marked on both sides. The side with the etchedRead More…

167

The parts were laser marked with a 20 watt q-switched ytterbium fiber laser with 160 mm focal length lens. The uid marking sample was annealed marked to create a nice contrast mark. It hadRead More…

168

Sample laser marking on automotive steel

169

A laser marking on steel

170

Laser marked steel

171

Laser marked steel  

172

Laser markings on steel  

173

 A sample laser marking on steel          

174

Laser markings on steel  

179

Company: CAT Radial parts marking.

180

Company: CAT The samples marked extremely well with the 20 watt Fiber Laser Marking System. Dark marks were placed on the steel tappets. The steel tappets had a cycle time of 7.73 seconds. ARead More…

182

Material: Silver plated 416 SS Power: 20 Watt Method used: Engraving Frequency: 40kHz Since there was not a rotary indexer configured at the time during the processing of this application, the mostRead More…

184

Sample laser marking on steel